Filters: Tags: numerical modeling (X)
68 results (39ms)|
Filters
|
Accurate input data are important for making site-specific projections of tidal wetlands into the future. We developed bias-corrected digital elevation models (DEM) using the LEAN approach (LiDAR Elevation Adjustment with NDVI). LEAN DEMs were used as the initial elevation for model projections. Further, we conducted elevation and vegetation surveys across each study site to characterize elevation profiles of dominant species, which were used to inform organic productivity functions in WARMER-2.
This dataset consists of physics-based Delft3D model and Delwaq model input files used in modeling sediment deposition and concentrations around the coral reefs of west Maui, Hawaii. The Delft3D models were used to simulate waves and currents under small (SC1) and large (‘SC2’) wave conditions for current stream discharge (‘Alt1’) and stream discharge with watershed restoration (‘Alt3’). Delft3D model results were subsequently used as forcing conditions for Delwaq models to simulate sediment transport and dispersion. The Delwaq models were used to simulate sediment transport and concentrations under the same two wave and stream discharge scenarios. The Delwaq models were run using forcing conditions generated by...
Categories: Data;
Tags: CMHRP,
Coastal and Marine Hazards and Resources Program,
Environmental Health,
Geography,
Geomorphology,
Time-series measurements of waves, currents, water levels, sea surface temperatures, ocean salinity, and water, air, and ground temperatures were collected in July through September 2011 in and around Arey Lagoon, near Barter Island, Alaska. Directional wave spectra, currents, water levels, salinity, and bottom and surface water temperatures were measured with a bottom-mounted 1MHz Nortek AWAC, HOBO temperature loggers, and a Solinst Levelogger in ~5m water depth offshore of Arey Island. Within Arey Lagoon, a bottom-mounted frame equipped with a Nortek 1MHz Aquadopp, Solinst Levelogger, and HOBO temperature loggers measured currents, water levels, and water temperatures. Ground temperatures (maximum depth 3 meters...
Categories: Data;
Tags: Arctic National Wildlife Refuge,
Arctic Ocean,
Arey Island,
Arey Lagoon,
Barter Island,
Time-series measurements of waves, currents, water levels, sea surface temperatures, ocean salinity, and water, air, and ground temperatures were collected in July through September 2011 in and around Arey Lagoon, near Barter Island, Alaska. Directional wave spectra, currents, water levels, salinity, and bottom and surface water temperatures were measured with a bottom-mounted 1MHz Nortek AWAC, HOBO temperature loggers, and a Solinst Levelogger in ~5m water depth offshore of Arey Island. Within Arey Lagoon, a bottom-mounted frame equipped with a Nortek 1MHz Aquadopp, Solinst Levelogger, and HOBO temperature loggers measured currents, water levels, and water temperatures. Ground temperatures (maximum depth 3 meters...
Categories: Data;
Tags: Arctic National Wildlife Refuge,
Arctic Ocean,
Arey Island,
Arey Lagoon,
Barter Island,
The data is derived from a Soil-Water Balance model for New Hanover, Brunswick, and Pender counties for the years 1979-2016 which is located on the USGS Model Node.
WARMER-2 Model Inputs and Projections for Three Tidal Wetland Sites Across San Francisco Bay Estuary
Understanding the rates and patterns of tidal wetland elevation changes relative to sea-level is essential for understanding the extent of potential wetland loss over the coming years. Using an enhanced and more flexible modeling framework of an ecosystem model (WARMER-2), we explored sea-level rise (SLR) impacts on wetland elevations and carbon sequestration rates through 2100 by considering plant community transitions, salinity effects on productivity, and changes in sediment availability. We incorporated local experimental results for plant productivity relative to inundation and salinity into a species transition model, as well as site-level estimates of organic matter decomposition. The revised modeling framework...
Transport of material in an estuary is important for water quality and hazards concern. We studied these processes in the Hudson River Estuary, located along the northeast coast of the U.S. using the COAWST numerical modeling system. A skill assessment of the COAWST model for the 3-D salinity structure of the estuary has been successfully studied in the past, and the present research extended that understanding to look at both physical and numerical mixing. The model grid extends from the south at the Battery, NY to the north in Troy, NY. The simulation is performed from March 25 to July 11, 2005 (111 days). For more information see: https://doi.org/10.5066/P95E8LAS.
Categories: Data;
Types: Map Service,
NetCDF OPeNDAP Service,
OGC WMS Layer;
Tags: CMG_Portal,
Earth Science > Human Dimensions > Natural Hazards > Floods,
Earth Science > Oceans > Marine Sediments >Sediment Transport,
Earth Science > Oceans > Ocean Circulation > Ocean Currents,
Earth Science > Oceans > Ocean Temperature > Potential Temperature,
A three-dimensional hydrodynamic and sediment transport model application of the mouth of the Columbia River (MCR) was constructed using the Delft3D4 (D3D) modeling suite (Deltares, 2021) to simulate water levels, flow, waves, and sediment transport for time period of September 22, 2020 to March 10, 2021. The model was used to predict the dispersal of sediment from a submerged, nearshore berm composed of sediment that was dredged from the entrance to the MCR navigation channel and placed on the northern flank of the ebb-tidal delta. This data release describes the development and validation of the model application and provides input files suitable to run the models on D3D software version 4.04.01.
Categories: Data;
Tags: CMHRP,
Clatsop County,
Coastal and Marine Hazards and Resources Program,
Columbia River,
PCMSC,
This data release includes representative cluster profiles (RCPs) from a large (>24,000) selection of coral reef topobathymetric cross-shore profiles (Scott and others, 2020). We used statistics, machine learning, and numerical modelling to develop the set of RCPs, which can be used to accurately represent the shoreline hydrodynamics of a large variety of coral reef-lined coasts around the globe. In two stages, the data were reduced by clustering cross-shore profiles based on morphology and hydrodynamic response to typical wind and swell wave conditions. By representing a large variety of coral reef morphologies with a reduced number of RCPs, a computationally feasible number of numerical model simulations can be...
Categories: Data;
Types: NetCDF OPeNDAP Service;
Tags: CMHRP,
Coastal and Marine Hazards and Resources Program,
Commonwealth of the Northern Mariana Islands,
Marine Geology,
PCMSC,
Time-series measurements of waves, currents, water levels, sea surface temperatures, ocean salinity, and water, air, and ground temperatures were collected in July through September 2011 in and around Arey Lagoon, near Barter Island, Alaska. Directional wave spectra, currents, water levels, salinity, and bottom and surface water temperatures were measured with a bottom-mounted 1MHz Nortek AWAC, HOBO temperature loggers, and a Solinst Levelogger in ~5m water depth offshore of Arey Island. Within Arey Lagoon, a bottom-mounted frame equipped with a Nortek 1MHz Aquadopp, Solinst Levelogger, and HOBO temperature loggers measured currents, water levels, and water temperatures. Ground temperatures (maximum depth 3 meters...
Categories: Data;
Tags: Arctic National Wildlife Refuge,
Arctic Ocean,
Arey Island,
Arey Lagoon,
Barter Island,
Here we present surface current results from a physics-based, 3-dimensional coupled ocean-atmosphere numerical model that was generated to understand coral larval dispersal patterns in Maui Nui, Hawaii, USA. The model was used to simulate coral larval dispersal patterns from a number of existing State-managed reefs and large tracks of reefs with high coral coverage that might be good candidates for marine-protected areas (MPAs) during 8 spawning events during 2010-2013. The goal of this effort is to provide geophysical data to help provide guidance to sustain coral health in Maui Nui, Hawaii, USA. Each model output run is available as a netCDF file with self-contained attribute information. Each file name is appended...
Categories: Data;
Types: Citation,
Map Service,
NetCDF OPeNDAP Service,
OGC WFS Layer,
OGC WMS Layer,
OGC WMS Service;
Tags: CMGP,
Coastal and Marine Geology Program,
Geophysics,
Hawaii,
Kahoolawe,
A series of tracer experiments were conducted biannually at the start and end of the vegetation growing season in a surface flow wastewater treatment wetland located near Phoenix, AZ. Tracer experiments were conducted prior to and following reconfiguration and replanting of a 1.2 ha treatment wetland from its original design of alternating shallow and deep zones to incorporate hummocks (shallow planting beds situated perpendicular to flow). Tracer test data were analyzed using analysis of moments and the one-dimensional transport with inflow and storage numerical model to evaluate the effects of the seasonal vegetation growth cycle and hummocks on solute transport. Following reconfiguration, vegetation coverage...
Categories: Publication;
Types: Citation;
Tags: OTIS,
constructed wetlands,
numerical modeling,
solut
This model archive makes available the U.S. Geological Survey Soil-Water-Balance (SWB) model created in support of a groundwater flow model of the former Badger Army Ammunition Plant in Sauk County, Wisconsin. The SWB model provides initial estimates of potential recharge to the groundwater system in the study area, which are used in a calibrated 3-dimensional MODFLOW (modular finite-difference flow) model. The SWB and MODFLOW models run from 1980 to 2020. The model incorporates changing land use, and changes reflecting the decomissioning of the plant (changing urban back to non-urbanized). SWB output is broken up into 50 model timesteps for the MODFLOW model.
The Coupled Ocean-Atmosphere-Wave-Sediment Transport (COAWST; Warner and others, 2019; Warner and others, 2010) model was used to simulate ocean circulation, waves, and sediment transport in Cape Cod Bay, MA. Larger scale simulations of the US East Coast (Warner and Kalra, 2022) were used to drive numerical grids covering the Gulf of Maine (~1000m resolution) with a two-way nested downscaled region into Cape Cod Bay (~250m resolution). Results were analyzed to investigate bay-scale dynamics of net transport, seafloor elevation changes, and net sediment fluxes. Those results were further used to drive a coastal scale grid that stretched along ~17km of the coast from the Cape Cod Canal to Sandy Neck Beach. This nearshore...
Categories: Data;
Types: Map Service,
NetCDF OPeNDAP Service,
OGC WMS Layer;
Tags: CMG_Portal,
Earth Science > Human Dimensions > Natural Hazards > Floods,
Earth Science > Oceans > Marine Sediments >Sediment Transport,
Earth Science > Oceans > Ocean Circulation > Ocean Currents,
Earth Science > Oceans > Ocean Temperature > Potential Temperature,
This data set consists of physics-based Delft3D-FLOW and SWAN hydrodynamic models input files used to study the wave-induced 3D flow over spur-and-groove (SAG) formations. SAG are a common and impressive characteristic of coral reefs. They are composed of a series of submerged shore-normal coral ridges (spurs) separated by shore-normal patches of sediment (grooves) on the fore reef of coral reef environments. Although their existence and geometrical properties are well documented, the literature concerning the hydrodynamics around them is sparse. Here, the three-dimensional flow patterns over SAG formations, and a sensitivity of those patterns to waves, currents, and SAG geometry were examined. Shore-normal shoaling...
A one- and two-dimensional hydrodynamic model of the San Francisco Bay and Delta was constructed using the Delft3D Flexible Mesh Suite (Delft3D FM; Kernkamp and others, 2011; https://www.deltares.nl/en/software/delft3d-flexible-mesh-suite/) to simulate still water levels. Required model input files are provided to run the model for the time period from October 1, 2018, to April 30, 2019. This data release describes the construction and validation of the model application and provides input files suitable to run the model on Delft3D FM Suite 2020.04. Model Description The San Francisco Bay and Delta Still Water Level Model (SFBD-SWL) utilizes the open-source Delft3D Flexible Mesh Suite (Delft3D FM; Kernkamp and...
Dynamically downscaled future wave projections from SWAN model results for the main Hawaiian Islands
Projected wave climate trends from WAVEWATCH3 model output were used as input for nearshore wave models (for example, SWAN) for the main Hawaiian Islands to derive data and statistical measures (mean and top 5 percent values) of wave height, wave period, and wave direction for the recent past (1996-2005) and future projections (2026-2045 and 2085-2100). Three-hourly global climate model (GCM) wind speed and wind direction output from four different GCMs provided by the Coupled Model Inter-Comparison Project, phase 5 (CMIP5), were used as boundary conditions to the physics-based WAVEWATCH3 numerical wave model for the area encompassing the main Hawaiian islands. Two climate change scenarios for each of the four GCMs...
A set of physics-based XBeach Non-hydrostatic hydrodynamic model simulations (with input files here included) were used to evaluate how varying carbonate budgets, and thus coral reef accretion and degradation, affect alongshore variations in wave-driven water levels along the adjacent shoreline of Buck Island Reef National Monument (BUIS) for a number of sea-level rise scenarios, specifically during extreme wave conditions when the risk for coastal flooding and the resulting impact to coastal communities is greatest. These input files accompany the modeling conducted for the following publication: Toth, L.T., Storlazzi, C.D., Kuffner, I.B., Quataert, E., Reyns, J., McCall, R.T., Stathakopoulos, A., Hillis-Starr,...
Categories: Data;
Tags: Bathymetry and Elevation,
CMHRP,
Climatology,
Coastal and Marine Hazards and Resources Program,
Ecology,
Simulatations of water levels in the Salish Sea for a continuous hindcast of the period October 1, 1985, to September 30, 2015 were conducted to evaluate the utility and skill of a sea-level anomaly predictor and to develop extreme water level estimates accounting for decadal climate variability. The model accounts for sea level position, tides, remote sea-level anomalies, local winds and storm surge and stream flows as they affect water density. Comparison of modeled and measured water levels showed the model predicts extreme water levels at NOAA tide gage stations within 0.15 m. Model inputs and outputs of time-series water levels along the -5 m depth isobath are presented. In addition, extreme water level recurrence...
Categories: Data;
Tags: CMHRP,
Climate Change,
Coastal and Marine Hazards and Resources Program,
Distributions,
Extreme Weather,
This model archive makes available the calibrated Soil-Water-Balance (SWB) model used to simulate potential recharge for the Mississippi Alluvial Aquifer for 1915 to 2018. The model was calibrated using monthly values of evapotranspiration and annual values of runoff and recharge for 19 drainage basins selected from within or nearby the Mississippi Alluvial Aquifer system. The calibrated SWB model and its use are described in the associated U.S. Geological Survey Open-File Report 2021-1008. The model was used to create output at two different scales: 1,609-meter and 1,000-meter grid cells. Also included are files used to generate a high-resolution (100-meter) subset of output for an area near Shellmound, Mississippi....
|
|
